Issue |
Matériaux & Techniques
Volume 99, Number 2, 2011
Numéro thématique : Indentation à différentes échellesTopical Issue: Indentation at different scales |
|
---|---|---|
Page(s) | 239 - 244 | |
Section | Appliquer l'indentation | |
DOI | https://doi.org/10.1051/mattech/2011027 | |
Published online | 21 July 2011 |
Mechanical properties of PVD Al1−xCrxN thin films
Propriétés mécaniques des films minces PVD Al1−xCrxN
Institut Pprime, UPR 3346 CNRS, University of
Poitiers, ENSMA, SP2MI, Bd Marie et
Pierre Curie, BP
30179, 86962
Futuroscope Cedex,
France
e-mail: phamhtrambk@yahoo.com
Received:
20
November
2010
Accepted:
17
March
2011
Al1−xCrxN thin films have been sputter deposited using either ion-beam (IBS) or magnetron. The structure, mechanical properties and residual stress state have been investigated using X-Ray diffraction, curvature measurements and nano-indentation. The presence of a ⟨200⟩ fiber texture associated with compressive global stresses was evidenced in the studied 0.6–0.85 Cr at.% range with the largest level for IBS. In-grain stresses were determined to be compressive for IBS while tension was found in the case of magnetron sputtering. The obtained stress-free lattice parameters a0 revealed difference between the processes, IBS being more energetic. The in-grain residual stress values of IBS samples are twice as large as those obtained using curvature method; this might be due to ⟨ 200 ⟩ texture effects and/or an over estimate of the elastic moduli. Hardness of the films was obtained in a range extending from 16 to 27 GPa correlated to residual stress level when compared to literature.
Résumé
Des films Al1−xCrxN ont été obtenus par pulvérisation en utilisant soit des faisceaux d’ions (IBS) soit du magnétron. La structure, les propriétés mécaniques et l’état de contraintes résiduelles ont été étudiés par diffraction X, mesure de courbure et nano-indentation. La présence d’une texture de fibre ⟨200⟩ associée à des contraintes globales de compression a été observée dans la gamme étudiée de 0,6–0,85 %.at Cr., les niveaux les plus élevés étant obtenus par IBS. Les contraintes intra-granulaires ont été déterminées en compression pour l’IBS et en tension dans le cas de la pulvérisation magnétron. Les paramètres libres de contrainte associés a0 révèlent une différence très nette entre ces deux procédés, l’IBS étant plus énergétique. Les contraintes intra-granulaires des échantillons sont deux fois plus élevées que les contraintes globales obtenues par la courbure; ceci pourrait être dû à des effets de texture et/ou à la sur estimation des modules élastiques. Les valeurs des duretés mesurées dans les films varient dans la gamme allant de 16 à 27 GPa et sont corrélées au niveau des contraintes résiduelles si l’on se réfère à la littérature.
Key words: AlCrN / PVD thin film / nano-indentation / sin2 ψ method
Mots clés : AlCrN / film mince PVD / nano-indentation / méthode des sin2 ψ
© EDP Sciences, 2011
Current usage metrics show cumulative count of Article Views (full-text article views including HTML views, PDF and ePub downloads, according to the available data) and Abstracts Views on Vision4Press platform.
Data correspond to usage on the plateform after 2015. The current usage metrics is available 48-96 hours after online publication and is updated daily on week days.
Initial download of the metrics may take a while.